EASY TO LOCATE CERTIFIED ONAN RV SERVICE AND PARTS DEALERS Onan has trained, tested and certified over 1,000 Onan RV Service Dealers covering most major metropolitan areas in the U.S. To easily locate the certified Onan Service Dealer, no matter where you travel, call 1-800-888-ONAN and ask us to send you an RV Service.
- Onan 0149-2279 Marquis 5000, 6500 & 7000 Fuel Filter(specs A-F) In Stock Normally: $11.43. Onan A047N923 Generator Low-Pressure Fuel Pump Out of Stock Normally: $127.18. Onan 191-2416 Generator Starter Motor With 16 Tooth Gear In Stock Normally: $145.24.
- Amazon's Choice for onan marquis 7000 parts. Cummins Onan 122-0836 Oil Filter. 4.9 out of 5 stars 878. Save more with Subscribe & Save.
- Ok I have an onan 7000 generator and I have replaced the carb and the control board and started the gen today and it died after about 6 minutes but I was sitting steal it runs a little longer when I am driving when I first put it back n I drive it around 830 at night and it did fine but today it died after about 20 min while driving and after taken the cover off and driving I restarted it.
- Commercial Marquis 7000 GenSet 6.5 NHM-FA/26115 LP 60 6500 120 54.2 1 1 (2. EASY TO LOCATE CERTIFIED ONAN SERVICE AND PARTS DEALERS - Onan. Operators Manual (981-0153), Parts Manual (981. Filename: cm-7000.pdf - Read File Online - Report Abuse.
If you blink you may miss it. That may be a bad pun, but it is the truth when it comes to Onan generators. When something goes wrong, the generator will send out a code to tell you the problem. If you blink, you may miss the number of the error code.
How to Read Onan Generator Fault Codes: It's not hard to read the Onan Fault Code blink system, once you get used to it. They use a blink and pause design to make their numbered codes clear and not confusing. For example, if the light blinks 5 times then pauses, then blinks 1 more time, that signifies Fault Code 51.
To learn more about the different Onan Fault Codes, what they mean and how to fix the problem, just keep reading our article. All the information is here for you to learn from. Onan Fault Codes are easy to learn if you do not blink while they are sending their message.
Onan Generator Fault Code List
Code 2 - Low Oil Pressure
This code will only blink twice. Idvd 7.0 4 free for mac. It shows that the generator is low on oil and you need to add more. Twist off the yellow cap to look at the gauge and see how much more you need to put in.
Just remember to not over-fill your oil tank. Too much oil is not a good thing
Code 3 - Service Check
When you see this code, it indicates that there is a problem somewhere on your Onan generator. You will get 3 flashes then a pause, then 3 flashes, then a pause and on it goes till you press the button to get the secondary code.
The secondary code will give you the specific problem that is wrong with your generator
Code 4 - Over Crank
The first thing you need to do when you see this code is to try to reset your control board. You do this by turning the switch off and then hit the reset button. Next, you need to turn the switch back to run. If it starts you are fine. If it doesn't and the code returns, then you need a new control board
Code 12 - Over Voltage
This problem comes from a faulty inverter and that part is overcharging the generator. The only way to solve this Fault Code problem is to take the generator to a qualified Onan dealer or repair shop.
Alternative sources for this code may be a lack of fuel or a clogged filter problem. Then you just add more fuel or replace/clean the filter
Code 13 - Under Voltage
This code tells you that the controller is incapable of maintaining proper voltage levels. There is a simple fix to this problem. Unplug all unneeded appliances while the air conditioner and battery charger are running.
Another source for this problem would be that the engine slowed down for a variety of reasons like a lack of fuel.
Code 14 - Over Frequency
This code tells you that the engine is running too fast and the sources for this code could be one of the following reasons: air leak at the intake, carb, and linkages not properly installed, misadjusted governor, broken governor.
Check your frequency levels first. Then clean or replace your carb, check to make sure the linkage is not reversed or replace the governor. For more info, read our Onan generator fault code 14 guide.
Code 15 - Under Frequency
This is the opposite of the above code. When you see this number, your engine is running too slow. The solution may be that everything was not connected properly or that the governor is in the wrong spot. It has to be in the 5thnotch from the right.
If the generator still flashes, you may have restarted your generator in under a minute and are running in ERO mode. You get the engine running but no power in this mode. Turn the generator off and wait for at least 2 minutes before restarting.
Code 19 - Governor Actuator Overload
The governor has one wire to the controller and one wire for ground. If either one is loose, that will trigger this code. All you have to do is tighten the loose wire and you should be good to go.
If that doesn't work or the wires are tight, the manual states that you are to go to a certified Onan repairman and get the problem looked at.
Code 23 - Low Oil Pressure Cutoff Switch
This code would indicate a problem with the cutoff switch itself. There is a malfunction in the switch and you probably won't be able to fix it yourself.
The manual states that you need to go to the nearest certified Onan dealer to get the problem solved for you. There will be a lot of these type of solutions throughout this code explanation
Code 27 - Voltage Sense Error
What this fault code tells you is that the controller cannot sense the output voltage. Again, this problem may be beyond your expertise to repair. The manual states that the only solution is to go to your authorized Onan dealer to rectify the issue.
Code 29 - High Battery Voltage
https://tratcontenbret1989.wixsite.com/downloadingaustin/post/fortnite-battle-royale-e. This is the simple way to say that the voltage across your battery system is more than 19 volts. Treyarch customer support chat. What you need to do is check your battery bank connections and if necessary, reconnect them in the proper order.
12-volt connections need to be parallel and 24-volt connections are done n a series. Another solution would be to set a lower battery boost charge rate
Code 31 – Overspeed
3 flashes, a pause and then one flash tells you that your Onan generator is going faster than 3,400 rpm. The trick here is to make sure you do not confuse 13 with 31. You can double-check by pressing the stop button 3 times in 5 seconds.
Once you return to the initial 3 flashes press the stop button again to get the secondary code to double-check your first reading. When you confirm the 31 code, you need to take the generator to the certified Onan dealer to get it fixed
Code 32 - Low Cranking Speed
This code informs you that your cranking speed is below 180 rpms for 2 seconds. To solve this problem, you need to clean the battery connections, or recharge/replace the batteries or replace the engine oil with the proper viscosity
Code 35 - Control Card Failure
During a self-test you may see this code pop up. The generator is telling itself that there is an error in the microprocessor EEPROM. You won't be able to fix this issue and need to take it to the certified Onan dealer near you.
Code 36 - Engine Stopped
That is without command by you. You could be out of fuel or you have a low LPG pressure issue, or your spark plug leads may be loose, or you have bad spark plugs. Finally, you may have to clean or replace the air cleaner or check for some other mechanical failure.
Code 37 - Invalid Generator Set Configuration
This simple message simply says that your Onan generator is set at the wrong frequency. To correct this issue, you should see your certified Onan dealer. They have the right tools to handle this problem
Code 38 - Over Current (Field Overload)
Or in simple English, you have too many appliances running at the same time. Also, you should check your air conditioner and other appliances to make sure there is not a problem with them.
Code 41 - Generator Rotor
Your controller is not sensing either field or output voltage. This is probably another issue you will not be able to fix yourself and the manual says for you to take your generator to an authorized Onan dealer for repairs.
Code 42 – Processor
This number tells you that your Onan generator detected an error within its Microprocessor Rom section. Again, you should not tackle this problem yourself but take your generator to your nearest certified Onan dealer.
Onan Marquis 7000 Generator Parts
Code 43- Processor Fault Code.
There is a problem with the Microprocessor RAM and see above to find the fix.
Code 45 - Speed Sense
All this fault code is saying is that your controller is not sensing the quadrature frequency. The simple fix for this issue is for you to bring your generator into the certified Onan dealer's shop and let them fix it for you.
Code 47 – Ignition
The manual states that you need to go to the nearest certified Onan dealer to get the problem solved for you. There will be a lot of these type of solutions throughout this code explanation
Code 27 - Voltage Sense Error
What this fault code tells you is that the controller cannot sense the output voltage. Again, this problem may be beyond your expertise to repair. The manual states that the only solution is to go to your authorized Onan dealer to rectify the issue.
Code 29 - High Battery Voltage
https://tratcontenbret1989.wixsite.com/downloadingaustin/post/fortnite-battle-royale-e. This is the simple way to say that the voltage across your battery system is more than 19 volts. Treyarch customer support chat. What you need to do is check your battery bank connections and if necessary, reconnect them in the proper order.
12-volt connections need to be parallel and 24-volt connections are done n a series. Another solution would be to set a lower battery boost charge rate
Code 31 – Overspeed
3 flashes, a pause and then one flash tells you that your Onan generator is going faster than 3,400 rpm. The trick here is to make sure you do not confuse 13 with 31. You can double-check by pressing the stop button 3 times in 5 seconds.
Once you return to the initial 3 flashes press the stop button again to get the secondary code to double-check your first reading. When you confirm the 31 code, you need to take the generator to the certified Onan dealer to get it fixed
Code 32 - Low Cranking Speed
This code informs you that your cranking speed is below 180 rpms for 2 seconds. To solve this problem, you need to clean the battery connections, or recharge/replace the batteries or replace the engine oil with the proper viscosity
Code 35 - Control Card Failure
During a self-test you may see this code pop up. The generator is telling itself that there is an error in the microprocessor EEPROM. You won't be able to fix this issue and need to take it to the certified Onan dealer near you.
Code 36 - Engine Stopped
That is without command by you. You could be out of fuel or you have a low LPG pressure issue, or your spark plug leads may be loose, or you have bad spark plugs. Finally, you may have to clean or replace the air cleaner or check for some other mechanical failure.
Code 37 - Invalid Generator Set Configuration
This simple message simply says that your Onan generator is set at the wrong frequency. To correct this issue, you should see your certified Onan dealer. They have the right tools to handle this problem
Code 38 - Over Current (Field Overload)
Or in simple English, you have too many appliances running at the same time. Also, you should check your air conditioner and other appliances to make sure there is not a problem with them.
Code 41 - Generator Rotor
Your controller is not sensing either field or output voltage. This is probably another issue you will not be able to fix yourself and the manual says for you to take your generator to an authorized Onan dealer for repairs.
Code 42 – Processor
This number tells you that your Onan generator detected an error within its Microprocessor Rom section. Again, you should not tackle this problem yourself but take your generator to your nearest certified Onan dealer.
Onan Marquis 7000 Generator Parts
Code 43- Processor Fault Code.
There is a problem with the Microprocessor RAM and see above to find the fix.
Code 45 - Speed Sense
All this fault code is saying is that your controller is not sensing the quadrature frequency. The simple fix for this issue is for you to bring your generator into the certified Onan dealer's shop and let them fix it for you.
Code 47 – Ignition
Once again the issue lies with the controller. It is not in bad shape, but it cannot sense any ignition when you try to start your generator. This also is an issue for your certified Onan dealer to handle.
Code 48 - Generator Field Sense
Once again, the controller is unable to sense a vital part of your generator's operating system. This time it is the field voltage that escapes its attention. See your authorized Onan dealer to fix this problem.
Code 51 – Processor
This is another key code telling you that there is a problem with the installed microprocessor. Syobon action mac. You will need to see your qualified Onan dealer to get this taken care of.
Code 52 - Fuel Injector
Here you have an open or short circuit in your fuel injector. This is another problem the manual says you need to take to your Onan dealer to get it taken care of.
Code 54 - MAT Sender
The MAT sender has an open or short circuit in it and it may be beyond your abilities to fix yourself. The manual states to bring your generator to your trusty Onan dealer to fix.
Code 56 - MAP Sender
This is not the same as the MAT. But the problem is the same with an open or short circuit in your MAP sender. The solution is the same as your Mat solution.
Code 57 - Over Prime
When your prime mode goes past 3 minutes, then this error code will appear. Check for and then remove any object that may be keeping the control switch in the prime position
Code 58 - Exhaust Gas Temperature Shutdown
What causes this error code is a lean fuel supply, restricted exhaust system, bad ignition system, bad heat sensor, and other issues. To keep your warranty valid, you need to take your generator to your Onan dealer for diagnosis and repair.
Code 81 - Exhaust Gas Temperature Sensor Open
This may mean that your temperature sensor is stuck open and will not close. It is best if you take your generator to your local Onan dealer to have them repair the problem
Code 82 - Exhaust Gas Temperature Shorted
You have a possible short circuit and it is a problem you should not deal with yourself. Your local authorized Onan dealer has the tools and expertise to fix this issue for you
Onan Generator Code Reset
Resetting your Onan Generator is not that difficult. All you have to do is follow these simple steps and you should be fine:
- Locate the primer button. This doubles as the start and stop button on your generator
- Hold the button down for about 30 seconds- Release the button and then start your generator
- Run the generator for 15 minutes to see if the code has been cleared. If not, then you may need the help of a qualified nan repairman to fix the problem
Some Final Words
Technology does bring a lot of wonderful toys to your life. It also helps make your life a little simpler. But the one drawback to new technology is that there is always some new problem that can arise.
That is why learning and understanding fault codes is so important. Once you learn and understand them you know what you have to do to solve the problem That knowledge also makes life a little simpler to live
Don't be afraid of technology, learn how to use it and learn the fault codes so you know what needs to be done next before you cause more problems that may raise your repair costs.
Warning, Caution, and Note Styles Used In This Manual. Watts .
( available from Cummins Onan) is bolted or a collar to which the tailpipe is. Appendix B. WIRING DIAGRAMS .
This is the service manual for the Series BGM and. NHM generator When contacting Onan for parts, service or product. Service Manual.
HGJAA, HGJAB, HGJAC, . WIRING DIAGRAM—HGJAD . .
WIRING . printed with the number '9' with Onan Part.
Number What spec is it? I have a Marquis NHM, Spec D I can send along.
Also have a service manual for a Spec J-P (in case you don't know the. WIRING DIAGRAM-HGJAA .
Cummins Onan Marquis 7000 Parts Manual
Diagram: Insulation - NEMA Class F. Ambient 40° C.
See the Parts Manual for When contacting Onan for parts and product infor-.Onan Marquis Generator Parts ~ hello friends our site, this is images about onan marquis generator parts posted by Alice Ferreira in Onan category on Nov 15, You can also find other images like wiring diagram, parts diagram, replacement parts, electrical diagram, repair manuals, engine diagram, engine scheme, wiring harness, fuse box, vacuum diagram, timing belt, timing .
The Onan Motor Generator is powered by a two cylinder - four cycle horizontally opposed gasoline engine. An automotive type starter is used to start the engine.
The starter is powered by a battery located in the motor generator compartment. of the genset subassemblies. Genuine Onan re-placement parts are recommended for best results.
When contacting Onan for parts, service or product information, be ready to provide the model number and the serial number, both of which appear on the genset nameplate.
See Table for the signifi-cance of each character of the model number and.
7000 Onan Marquis Generator
onan marquis ? 7nhmfac, the start switch on the generator starts and stops ok.
the remote switch starts, but when released will stop, also will not shut off generator if started with generator switch, sounds like a load on generator. Onan Marquis Parts Diagram ~ thank you for visiting our site, this is images about onan marquis parts diagram posted by Maria Rodriquez in Onan category on Nov 24, You can also find other images like wiring diagram, parts diagram, replacement parts, electrical diagram, repair manuals, engine diagram, engine scheme, wiring harness, fuse box, vacuum diagram, timing belt, timing.Onan pdf Manual????
- iRV2 ForumsMarquis wiring diagram no output - SmokStak
